“I applied the wax days ago and it is still tacky”
Does this sound like you? If it does, guess what? Unless you live in a rain forest where the humidity is 100%, I would bet you dollars to donuts- that you applied too much wax!
Now what?
Well, most of what I am going to share applies to if you only used Annie’s Clear Wax. NOT if you used the Dark Wax. (that is because the Dark Wax has a stain in it and besides adding a layer of protection- you used the Dark Wax because the stain gives it an aesthetic effect. So, to start removing some after it has dried- you may lift partial amounts of stain and get a mottled / funny result.) So – with that said- I am focusing here on tacky Clear Wax.:
First- I would like to direct you to watch my video on how I apply Clear Wax. If you have never watched- you should. Think about what you may have done differently than I, based on my instructions. Watch that video by clicking HERE.
So, if you have too much wax on your piece, first take a clean rag that has no residual wax on it from previous applications. Focus on that one area of your piece of furniture and rub it lightly for 20 seconds. Touch it. Has any of the tackiness disappeared? (I am hoping you said yes) Sometimes- that tackiness comes from not a thorough rub off. If this worked- you got lucky.
If however, the tackiness is still there…you most likely applied too much wax. All is not lost though. You learned something that you will not do again- I am sure. And- here are TWO options to remove the tackiness:
OPTION 1.
If the tackiness is minimal but you cannot stand it, consider applying a fresh coat of Clear Wax, based on how I instruct in my video noted above when it comes to removing the residual wax. That is because the fresh wax you apply will activate the top micro layer of the previous dried/tacky application. The critical part here – is when removing the excess do so as I instruct in the video. You should not have a tacky feeling when you glide your hand over the surface after wiping off the residual. A cool, slightly moist feeling is ok…but in general- you should be able to glide you hand smoothly. This fresh application should even it all out. (this is what I would do – assuming it is only CLEAR wax you used- not the dark)
NOTE- apply wax over the whole side or top…not just spot treat. But you do not need to wax the whole piece of furniture if you are having this issue only on the top.
OPTION 2.
So, the next step is to try a rag with a little odorless mineral spirits on it and wipe off some of that wax build up.
Your rag should be damp only, not dripping! I like to use “real” Mineral Spirits..meaning not the “green” Mineral Spirits that has a milky white appearance. I just don’t feel it works nearly as well as the original Mineral Spirits. Take your rag and place it on the opening of the Mineral Spirits. Flip the container a couple of times in different areas of the rag. (the image I want you to think of is how a person would put nailpolish remover onto a cotton swab or ball!) With a tiny bit of Mineral Spirits on your rag, rub the piece in the direction you applied the wax. (Meaning- do not going against the grain) This is particularly important with Dark Wax and where you applied it in strokes. The mineral spirits on the rag will remove some of the wax – but it won’t restore the piece as it was before you applied all of the Wax. You do not want to be aggressively scrubbing in any one spot- you want to have uniformed removal of the build up.
After using Mineral Spirits- give your piece time to “air dry”…meaning allow the residual mineral spirits that may still be slightly on the piece to evaporate. Once the piece has no moisture to it, you can consider sanding some of the wax off. This can take a bit of time and be messy if the wax is on really thick. If after the Mineral Spirits step- your piece feels better…skip the sanding.
Keep in mind- that if you do not like the look of it after this “corrective measures- with chalk paint, you can paint right over the wax and start again. However, if you just know that there is still quite a bit of fresh wax on the piece, Annie has recommended you give the wax ample time to cure. This could mean waiting about 4 weeks. Once you go to paint over the wax- there is no extra prep work needed. Just make sure the Wax has dried! You cannot repaint over freshly applied wax…clear or dark! That is like walking on quick sand- ..not a good thing.
But let’s help you avoid this issue! Please read the following before using wax for the first time.
Wax seems to cause the most confusion for customers… So, I hope the following is helpful for you!:
How Much Wax Do I apply? If all you take away from what I say and do is this…you will be ok! So, please take note … we are not icing a cake! We are waxing furniture. So, VERY THIN & UNIFORM coats are best.
Just like when you put moisturizer on your skin- you do not put a thick coat on, but rather a THIN coat and rub it in- so that it will be absorbed into your skin. OR when you use hair conditioner…you apply it and then do what? Rinse it off. That is because your hair will absorb what it needs. Annie’s Chalk Paint will do the same thing in regards to the wax! And you should never have so much wax on your brush that it is “caked” up the sides. If you have this- you are using too much wax and more importantly- wasting your wax.
Also- you never apply the wax and then leave it that way- YOU ALWAYS REMOVE THE RESIDUAL and wipe off the extra. Never- ever apply wax and leave it for hours or days before doing this!!!!! NEVER!
CLEAR WAX- this is how The Purple Painted Lady uses it:
1. I take a plastic spoon and a paper plate. Using the backside of the spoon- I take a good amount of wax out of the tin and put it on the paper plate. (Place the cover back on the tin of wax until you need more)
2. I use my wax brush and pull some of the wax from the glob (for lack of better words.) Only the tips of your wax brush bristles should have wax on them- there should not be wax covering up the side of the brush. A little goes a long way! Again- you are not icing a cake where you want a generous amount of thickness. We are applying the wax very thin- pressing uniformly with steady pressure- but not so much that you are bending the bristles on the wax brush. I like to use the analogy that this is similar to waxing your car…you apply the wax- BUT NOT SO MUCH that when it is time to wipe it off or buff- you need a power tool to do it! So- apply a thin layer of wax and GET IT IN THE GROOVES OF THE PAINT. Again- another analogy is a Thomas’s English Muffin. Think if the wax being butter. You want the butter to get into all the nooks & crannies. Same concept for the wax in regards to the paint.
3. APPLY WAX IN SECTIONS: I work in about 1 foot sections … I use a circular motion when applying the Clear Wax. Sometimes- depending on the piece- (except when going for that Rustic look or when you have a textured piece) I will apply the wax in the same direction as my painted brush strokes. Either way…circular or not….when I have finished waxing a whole side of the piece – I ALWAYS finish with a few clean straight wipes with my rag in the direction I painted and I am pushing the wax in and wiping off the extra. If I was doing a dresser top- I would start at the back reaching across while standing in front of the piece and as I apply the Annie Sloan wax – I work my way toward the front as so I don’t lean into a previously waxed area. You will see where you waxed prior because it does deepen the hue of the paint a slight amount but be aware of where you just waxed. I also overlap my waxing sections so I ensure that I do not leave any missed spots. 4. WIPE OFF WAX: After applying the wax to one section, I will notice when the wax is not covering as much- that is my queue I need more wax. But before reloading your wax brush….use a lint free cotton t-shirt (an old one from my husband or an old sheet) and I wipe off the residual wax with a couple wipes ..circular or in the same direction as I just waxed. (I am not buffing the wax at this stage! Merely just removing or incorporating any small wax “crumbs” that may be present.) Again- a few uniformed swipes or circular rubbing (but more if necessary) – and that is it. 5. Resume waxing the next area- I wax strategically – meaning in an organized direction so I do not miss a spot. And I overlap my last “section” just a smidge so I don’t miss any of the surface.
6. The wax will dry (meaning no longer be tacky to the touch within a short time….maybe an hour or two?) However a variable in the dry time is the temperature and humidity where you are located. Is it is humid and cooler- cure time will be longer. If it is taking a long time and your wax is still tacky and you are not in the rain forest- reread my warnings above regarding applying the wax thin!
Depending on the piece I am finishing- I may have different amounts of wax coats. For instance…..a dresser. I may have 2 – 3 coats of wax on the top, but only 1 coat of wax on the sides and front.
7. Once the piece is no longer tacky- if you want to have a shinier finish- buff your piece. If you like it as is- then you are done! It does not take much rubbing and the piece will be quite shiny- so pay attention and have good lighting so that you do not over do it.
8. Remember NO WAX when painting pieces for outside.
9. Surfaces that will get serious use (wear and tear) like tops of dressers and tables – should receive 2 to 3 coats of wax. If you are using Dark Wax, apply your clear wax coats first and let it thoroughly dry before doing a top layer of dark Wax! Follow the procedure above – always allow wax to dry between additional coats.
Please watch my wax video! Visit my VIDEOS Page here to do so!